بسم الله الرحمن الرحيم
السلام عليكم ورحمه الله وبركاته
Many devices such as Wi-Fi-cams get power being plugged into a nearby outlet through USB. But if you want to put this device somewhere where an outlet is not nearby, you can use existing Ethernet drops (or run Ethernet yourself) to operate the camera by using the handy adapter.
Keep in mind that some devices will already comes with Ethernet built in, which is used for both the power of the camera and connect it to the local network or the Internet. Others, such as Wi-Fi cameras, and will only get the power from the USB cable that plugged into the outlet using the power adapter. But if you have a house wired with Ethernet cables are moving all over the place, you can edit and use Ethernet port instead.
Before you begin, you need to make sure your Ethernet lines supports Power over Ethernet.
What is a Power over Ethernet (PoE) and?
As mentioned above, the cameras have the most wired Ethernet control built in, allowing them to take advantage of the so-called "Power over Ethernet" (or "Bo" for short). And it can transmit video and audio over Ethernet connection, but drawing power on the same cable as well.
However, in order to Bo to work, you need a router or Ethernet switch that supports Bo (it will have a habit of "Bo" written somewhere near the Ethernet ports). Otherwise, you can buy the so-called injector Bo, which will turn the ordinary into an Ethernet line support Bo Ethernet line. Basically, you are turning Ethernet cable from your cable data only cable that can transmit data and power.
How to add poE to a USB device with Bo adapter to USB?
If you have a router that supports Bo but the device that does not (in our case, Kam Wi-Fi, which counts more than USB), you can power this device over Ethernet with Bo adapter to the USB (sometimes called a traitor only Bo). You will need one that can provide 5 volts and 10 watts of power, which is most of them.
This $ 20 one works great, so it comes with a USB connector female (in the form of adapter) that will allow you to plug in any USB cable. Some splitters Bo does not come with USB connectors, but merely a power connector year, so watch out for it if it matters to your setup.
To install Bo adapter to USB, only locate an Ethernet drop the closest to your device. More than likely, perhaps you already have an Ethernet cable plugged into it, but that's not a problem.
Disconnect the cable and then plug in the Ethernet connector male from Bo Ethernet jack adapter.
Then, take the Ethernet cable that you plugged into the wall and connect it to an Ethernet connector female poE adapter.
Then, take the Ethernet cable that you plugged into the wall and connect it to an Ethernet connector female poE adapter.
If you do not have an existing Ethernet drops, but still want to run an Ethernet cable to your device, you will connect it to an Ethernet connector female Bo adapter and discard the males in that case connector.
In any case, now that you have an Ethernet segment every drug addict, take a female
USB adapter and plug it into the power connector in the poE adapter.
Then take the USB cable from the device and connected to the female USB connector.
Should automatically on power and connect the device to act like a regular outlet so all the time. Unfortunately, we have a Wi-Fi camera is not able to get an Internet connection of Ethernet cable, so we still need to connect it to our Wi-Fi network as usual, and make sure they are in the range we have directed. But Power over Ethernet worked well.
بسم الله الرحمن الرحيم
Keep in mind that some devices will already comes with Ethernet built in, which is used for both the power of the camera and connect it to the local network or the Internet. Others, such as Wi-Fi cameras, and will only get the power from the USB cable that plugged into the outlet using the power adapter. But if you have a house wired with Ethernet cables are moving all over the place, you can edit and use Ethernet port instead.
Before you begin, you need to make sure your Ethernet lines supports Power over Ethernet.
As mentioned above, the cameras have the most wired Ethernet control built in, allowing them to take advantage of the so-called "Power over Ethernet" (or "Bo" for short). And it can transmit video and audio over Ethernet connection, but drawing power on the same cable as well.
However, in order to Bo to work, you need a router or Ethernet switch that supports Bo (it will have a habit of "Bo" written somewhere near the Ethernet ports). Otherwise, you can buy the so-called injector Bo, which will turn the ordinary into an Ethernet line support Bo Ethernet line. Basically, you are turning Ethernet cable from your cable data only cable that can transmit data and power.
How to add poE to a USB device with Bo adapter to USB?
If you have a router that supports Bo but the device that does not (in our case, Kam Wi-Fi, which counts more than USB), you can power this device over Ethernet with Bo adapter to the USB (sometimes called a traitor only Bo). You will need one that can provide 5 volts and 10 watts of power, which is most of them.
This $ 20 one works great, so it comes with a USB connector female (in the form of adapter) that will allow you to plug in any USB cable. Some splitters Bo does not come with USB connectors, but merely a power connector year, so watch out for it if it matters to your setup.
To install Bo adapter to USB, only locate an Ethernet drop the closest to your device. More than likely, perhaps you already have an Ethernet cable plugged into it, but that's not a problem.
To install Bo adapter to USB, only locate an Ethernet drop the closest to your device. More than likely, perhaps you already have an Ethernet cable plugged into it, but that's not a problem.
Disconnect the cable and then plug in the Ethernet connector male from Bo Ethernet jack adapter.
Then, take the Ethernet cable that you plugged into the wall and connect it to an Ethernet connector female poE adapter.
Then, take the Ethernet cable that you plugged into the wall and connect it to an Ethernet connector female poE adapter.
If you do not have an existing Ethernet drops, but still want to run an Ethernet cable to your device, you will connect it to an Ethernet connector female Bo adapter and discard the males in that case connector.
In any case, now that you have an Ethernet segment every drug addict, take a female
USB adapter and plug it into the power connector in the poE adapter.
Then take the USB cable from the device and connected to the female USB connector.
Should automatically on power and connect the device to act like a regular outlet so all the time. Unfortunately, we have a Wi-Fi camera is not able to get an Internet connection of Ethernet cable, so we still need to connect it to our Wi-Fi network as usual, and make sure they are in the range we have directed. But Power over Ethernet worked well.
I ask God to have benefited
And I hope that I have I could deliver information to you
Do not forget to leave your comment if you get stuck
Also do not forget the wonders because these small pressure equal to a great encouragement for me
I hope to post Thread friends also benefit
Do not forget Likes page
To receive the all-new
I ask God to have benefited
And I hope that I have I could deliver information to you
Do not forget to leave your comment if you get stuck
Also do not forget the wonders because these small pressure equal to a great encouragement for me
I hope to post Thread friends also benefit
Do not forget Likes page
To receive the all-new
And I hope that I have I could deliver information to you
Do not forget to leave your comment if you get stuck
Also do not forget the wonders because these small pressure equal to a great encouragement for me
I hope to post Thread friends also benefit
Do not forget Likes page
To receive the all-new
0 التعليقات:
إرسال تعليق